2018-2019 Mountain Aire, Essex and London Aire


SilverLeaf Products and Locations
## Copied from 2017, WILL need appending ##

HMS365(H) - House Monitor System - (amidship)
OA600 - Oasis RV-C Node - (Oasis Compartment)
SPX300 - RV-C Monitor, External - (Water Works Comp)
TM102 JS465 - Total Coach Controller - (Electrical / 'Cord' Compartment)

VMS 640~650 - Digital Dash (Engine/ Trans Monitor)

vms-645 piccy

VMS-600 series provide a full "digital dash" with every analog gauge and indicator replaced by precise, accurate and stylish digital images in a complete cluster replacement. Offered in Country Coach, ForeTravel, Newmar, Newell and others, “Glass Dash” is also available as an aftermarket addition for most newer diesel pushers. Each version is unique, programmed to the specifications of the coach builder.

SP-600 - RV-C 6-button Keypad

SP600 Product Info Page


The SP600 is a wall-mounted, 6-button RV-C control unit which is used for Managing up to 6 unique functions via the RV-C network. Each of the 6 buttons are individually addressable. They may be used individually or in pairs for advanced functions. This may be for (lighting) Dimmers, Water Pump, motors or others on a design-by design basis within the RV-C controlled house systems of a coach or towable.

DB-100 - DC Distribution Board

DB-100 Product Info Page


The DB-100 is a DC-switching unit which is used for Managing up to 10 DC loads of 1 to 13 Amps. This may be (lighting) Dimmers, Locks, Water Pump or others on a design-by design basis within the house systems of a coach or towable. It uses the ubiquitous RV-C CAN-BUS found in modern coaches or those retrofitted for this.

DB-100 Part Numbers

TM-293 - Rixen Furnace / Heat Controller

TM293 Rixen Furnace Controller Product Info Page


Based on TM200 hardware, the TM-293 controls a Rixen furnace/water heater system.
It provides a single heat zone and control over the burner and water heater.

By way of the TM293, the Rixen Furnace may be activated via an HMS touch panel or SP600 keypad.

TM-290 - AC Power Monitor

TM290 AC Power Monitor Product Info Page

TM-240 Picture

AC Power Monitoring
The TM-290 has electronics based on the TM-240 only really varying in software configuration.

It monitors up to 3 AC Voltages and 1 AC Amperage. It reports as a Transfer Switch, and establishes the AC power source based on the voltage data. Only one unit can be used in an installation.

TM-260 - Slide, Awning, and Motor Controller

TM260 Slide, Awning, and Motor Controller Product Info Page

TM-200 Picture


The TM-260 is based on the TM-200 hardware. It varies only in software. It has the ability to control up to 6 devices – slide rooms, awnings, or shades –
and/or up to 15 DC outputs. In addition, it can provide up to three temperature readings.
Individual outputs may be set to operate thermostatically, based on any RV-C ambient
temperature reading. Its included in Fleetwood and Newmar newest builds.

TM-250 - AC Power Management Controller

TM250 AC Power Management Controller Product Info Page

TM-250 Picture

The TM-250 monitors AC power as-reported from the transfer switch directly (RV-C) or via the TM102. It then sheds AC loads to maintain a maximum on each leg. Devices are controlled through external relays. Loads are shed in a configurable order, and restored in the opposite sequence. The unit also supports up to three temperature sensors. The TM250 can be configured through the Omniscope diagnostic tool.

TM-240 - AC-DC Systems Data Collector

TM240 Systems (power) Data Collector Product Info Page
As a data collector, The TM240 reads Voltage and Amperage readings and supplies them (as well as the related errors) to the RV-C bus. Its inputs include AC, DC and Solar.

While principally suited for all Diesel coaches, its also a replacement solution as part of the Monaco/ Navistar/ Fleetwood's Aladdin upgrade system we supply.

TM-229 - Tile Heat Controller

TM229 Tile Heat Controller Product Info Page

TM220 Picture

The TM-229 can control and read temperatures of up to 4 floor mats. The TM229 is identical in hardware and software to the heat controllers TM220 and TM225. The TM229 differs in its configuration. It is only configured to control tile heat and can be configured through the Omniscope diagnostic tool.

If the Tile heat has suddenly stopped working--it may have failed. If so, it may be seen as a TM225 and may or may not report missing temp sensors.

Syndicate content